Available 
| Dimensions | Dimensional drawing: https://caas.production.phoenixcontact.coremedia.cloud/caas/v1/stable/media/22530/full/b250?format=jpg Width: 14.9 mm Height: 62.2 mm Depth: 62 mm |
| Notes | Utilization restriction EMC note: EMC: class A product, see manufacturer's declaration in the download area |
| Interfaces | SmartÃElement interface Number of interfaces: 1 Connection method: Card edge connector Transmission speed: See system in which you use the SmartÃElement. Start time until ready to operate: < 500 ms |
| System properties | Module ID code (hex): none Process data channel: 16 bit Input address area: 0 Byte Output address area: 2 Byte Required parameter data: 9 Byte Required configuration data: 6 Byte |
| Output data | Digital Output name: Digital outputs Connection method: Push-in connection Connection technology: 1-conductor Number of outputs: 16 Protective circuit: Short-circuit and overload protection; electronic Output voltage: 24 V Limitation of the voltage induced on circuit interruption: -32.8 VÃDC ... -15 VÃDC Maximum output current per module: 6 A (Also make sure that the maximum permissible current of 6ÃA is not exceeded.) Nominal output voltage: 24 VÃDC Load min.: 10 ké Output voltage when switched off: max. 1 V Output current when switched off: max. 300 õA Nominal load, inductive: 12 VA (1.2 H, 48 é, with nominal voltage) Nominal load, lamp: 12 W (at nominal voltage) Nominal load, ohmic: 12 W (48 é, with nominal voltage) Switching frequency: max. 1200 per second (With resistive load, at least 50ÃmA load current) max. 1 per second (with inductive load) max. 16 per second (with nominal lamp load) Reverse voltage resistance to short pulses: limited protection up to 0.5 A for 1 s Behavior with overload: Shutdown with automatic restart Behavior with inductive overload: Output can be destroyed Signal delay: max. 100 õs (when switched on) max. 100 õs (when switched off, with at least 50 mA load current) Overcurrent shut-down: min. 0.7 A Output current with ground connection interrupt when switched off: < 1 mA |
| Product properties | Type: modular Product type: I/O component Product family: Axioline SmartÃElements Mounting position: See the system in which the SmartÃElement is used. Insulation characteristics Overvoltage category: II (IEC 60664-1, ENÃ60664-1) Pollution degree: 2 (IEC 60664-1, ENÃ60664-1) |
| Electrical properties | Potentials: Communications power supply of the Smart Elements (U Supply voltage: using card edge connectors Potentials: I/O supply (U Supply voltage: 24 VÃDC (using card edge connectors) Supply voltage range: 19.2 VÃDC ... 30 VÃDC (including all tolerances, including ripple) Current draw: max. 6 A Current consumption: min. 40 mA (without connected peripherals) Power consumption: max. 180 W (of which 1.1ÃW internal losses) min. 288 mW Protective circuit: Surge protection; See the system in which the SmartÃElement is used. Reverse polarity protection; parallel diode Electrical isolation/isolation of the voltage ranges Test voltage: Communications supply / 24 V supply (I/O): 500 VÃAC, 50 Hz, 1 min. Test voltage: Communications supply / functional ground: 500 VÃAC, 50 Hz, 1 min. Test voltage: 24ÃV supply (I/O) / functional ground: 500 VÃAC, 50 Hz, 1 min. |
| Connection data | Connection technology Connection name: I/O Note on the connection method: Please observe the information provided on conductor cross sections in the ââ¬Ã AxiolineÃSmartÃElementsâ⬠user manual. With a small conductor cross section and high current, the terminal point temperature can reach up to 45ÃK above the ambient temperature. When selecting the cables, observe the permissible operating temperature in accordance with IEC or UL. Conductor connection Connection method: Push-in connection Conductor cross section rigid: 0.25 mm² ... 1.5 mm² Conductor cross section flexible: 0.25 mm² ... 1.5 mm² Conductor cross section AWG: 24 ... 16 Conductor cross section flexible, with ferrule without plastic sleeve: 0.25 mm² ... 1.5 mm² Conductor cross section, flexible, with ferrule, with plastic sleeve: 0.25 mm² ... 1.5 mm² Stripping length: 8 mm I/O Connection method: Push-in connection Note on the connection method: Please observe the information provided on conductor cross sections in the ââ¬Ã AxiolineÃSmartÃElementsâ⬠user manual. With a small conductor cross section and high current, the terminal point temperature can reach up to 45ÃK above the ambient temperature. When selecting the cables, observe the permissible operating temperature in accordance with IEC or UL. Conductor cross section, rigid: 0.25 mm² ... 1.5 mm² Conductor cross section, flexible: 0.25 mm² ... 1.5 mm² Conductor cross section AWG: 24 ... 16 Conductor cross section, flexible, with ferrule, with plastic sleeve: 0.25 mm² ... 1.5 mm² Conductor cross section flexible, with ferrule without plastic sleeve: 0.25 mm² ... 1.5 mm² Stripping length: 8 mm |
| Environmental and real-life conditions | Ambient conditions Ambient temperature (operation): -25°C ... 60°C Degree of protection: IP20 Air pressure (operation): 70 kPa ... 106 kPa (up to 3000Ãm above sea level) Air pressure (storage/transport): 70 kPa ... 106 kPa (up to 3000Ãm above sea level) Ambient temperature (storage/transport): -40°C ... 85°C Permissible humidity (operation): 5 % ... 95 % (non-condensing) Permissible humidity (storage/transport): 5 % ... 95 % (non-condensing) |
| Standards and regulations | Protection class: III (IEC 61140, ENÃ61140, VDEÃ0140-1) |
| Mounting | Mounting type: Smart Element slot Mounting position: See the system in which the SmartÃElement is used. |
Description other products
